• Createx uses the finest pigments available and the colors have a brightness and richness unmatched by others.
• These colors can be used on a variety of surfaces (i.e. fabrics, leather, canvas, paper, wood, ceramics, and clay) with permanent results.
• Createx Colors also produces airbrush additives and mediums which allow artists to "customize" the colors for specific applications
• Matte, Fluorescent, and Opaque Colors are available in: 2 oz., 4 oz., 8 oz., 16 oz., 32 oz. and gallon sizes.
• Pearlized, Chameleon, and Iridescent Colors are made in 2 oz., 4 oz. 8 oz, and gallon sizes.

See our information below for all the Color Types that CREATEX has: Transparent, Fluorescent, Opaque, Pearlized, Iridescent, and Additives.

CREATEX Product Data and Technical Information:

SURFACE PREPARATION
Fabric- Including 100% cotton, 50/50 blends, denim, sweatshirts, and most natural fibers.
1) For best results, wash item first to remove sizing and mill finishes.
2) Airbrush the design onto fabric avoiding thick buildup of paint and excessive paint layering.
3) Allow colors to dry, or a heat gun may be used to accelerate drying time. Drying time varies depending on application.
4) Heatset fabric for permanence by one of the following methods:
a) Iron for 2 minutes at 300 degrees F use a protective cloth, keep iron moving.
b) Turn item inside out and put in clothes dryer for 40 minutes at highest heat.

Leather
1) Clean leather by wiping with mineral spirits or rubbing alcohol.
2) For best results, lightly spray mist a base coat of Opaque White on areas to be sprayed.
3) Apply color, avoiding over saturation and excessive paint layering.
4) Allow colors to dry thoroughly before heat setting.
5) Iron for 30 minutes at 225 degrees F using a protective cloth, or use a hot air gun at highest level for five minutes.

Paper and Canvas
1) Apply Color, avoiding thick buildup.
2) When using high tack frisket, dilute colors 25% with water. Colors are permanent when dry.

Wood
1) Prepare surface by lightly sanding, wipe clean.
2) Apply color, avoiding thick buildup of paint. Allow colors to dry for 24 hours before applying clear finish.

Ceramics and Clay
1) Apply color in thin even coats, avoid thick buildup.
2) Do not exceed temperatures of 300 degrees F when baking. Colors are permanent for handling after 24 hrs.

TROUBLESHOOTING
Generally, Createx Airbrush Colors are ready to spray without any additives or modifications. But, depending on many factors including the type of airbrush gun used, tip and needle size, type of compressor, air pressure, humidity, occasional problems may arise. We suggest some experimenting and adjusting until smooth spray pattern is achieved. We offer many different mediums and additives to help gain maximum success. Following are some common airbrush problems and solutions.

Problem: Colors not spraying properly, including: spitting spraying to one side, paint leaking from gun, paint drying or building up in tip.
Solution:
1) Check for bent needle or tip, replace if necessary.
2) Check to make sure compressor is properly functioning. Try adjusting air pressure until colors spray in a smooth even pattern. Since some colors will spray differently than others, small adjustments may need to be made periodically to air pressure.
3) Createx Colors work best when using a "medium" sized airbrush needle and tip. If you are using a "fine" needle and tip, you may have to dilute the colors slightly with Airbrush Extender or water. Opaque, Pearlized, and Iridescent Colors tend to be thicker due to the additional solids needed for proper finish. Adjust color accordingly.
4) Spray Createx Airbrush Cleaner through the airbrush then flush with water.
5) Check color container that you attach to the airbrush for a blocked air hole.
6) Inadequate storage of paint including: Leaving cap open or paint exposed to air for prolonged periods of time, may have caused paint to dry in bottle.
a) Strain paint through a cheesecloth, nylons, or a fine strainer.
b) Dilute colors with a small amount of water until colors flow smoothly.
7) In dry, humid, or outdoor conditions Airbrush Extender or Retarder should be added to the paint to slow drying.

Problem: Airbrush is spitting water while you spray color.
Solution: Attach moisture trap to the air hose or let compressor cool.

Problem: Colors are fading after washing.
Solution:
1) Follow the appropriate heatsetting instructions.
2) If water was used to dilute colors, decrease amount or use Airbrush Extender instead.
3) Turn shirt inside out before washing. Avoid using bleach or Woolite. Wash in cold water.

AIRBRUSH COLOR TYPES
Transparent: For white and light colored surfaces only.Add Opaque Medium for opacity or to create pastel colors. May be intermixed with all other Createx Airbrush Colors.

Fluorescent: For white and light colored surfaces. For coverage on dark surfaces, base coat surface with Opaque White. Mix with transparent, pearlized, or other fluorescent colors.

Opaque: For both light and dark colored surfaces. Add Airbrush Extender to increase transparency. Add Opaque Medium to create pastel colors. May be mixed with other opaque or transparent colors.

Pearlized: Covers both light and dark colored surfaces. Colors have a shimmering metallic finish. Mix with other pealized, transparent, fluorescent, iridescent, and chameleons.

Iridescent: Covers both light and dark colored surfaces. Colors have a shimmering metallic look which changes at the angle of light. Mix with other iridescent, pearlized, transparent, or fluorescent colors.

ADDITIVES
Airbrush Extender: A transparent medium which will dilute the color to a lighter value. Will increase transparency in opaque and pearlized airbrush colors. Add until desired transparency or color shade is achieved.

Airbrush Opaque Base: Add to Createx transparent (matte) airbrush colors for added opacity. Extends opaque colors to a lighter value. See label for usage information.

Airbrush Cleaner: Highly concentrated, biodegradable cleaner for use with all water-based colors. Used to clean airbrushes, and color jars.

Airbrush Top Coat: Protective top coat which dries to a clear matte finish. Spray over finished airbrush design when dry. Permanent on most surfaces, including: fabric, paper, wood, metal, plaster, canvas, leather. See label for usage information.

Airbrush Gloss Coat: Protective top coat which dries to a clear gloss finish. Spray over finished airbrush design when dry. Permanent on most surfaces, including: fabric, paper, wood, metal, plaster, canvas, leather. See label for usage information.

Airbrush Retarder: Add to Createx Airbrush Colors to enhance flow and prevent tip drying in dry or humid conditions. Add 3 drops per 1 oz. of color. See label for additional usage information.

CHECKOUT

After winning an item in auction or completing a Buy-It-Now purchase, you have two check-out options:

Check-Out Now! Click on the Check-Out button at the top of this page or click here to immediately proceed with the checkout and payment process. You will be able to complete your payment and finalize your purchase without waiting for the winning bidder email confirmation.

Check-Out Later: Within 2 hours of the end of the auction, you will be notified via email that you are the winning bidder. There is no need to contact us to arrange payment. Our email will contain a link to our checkout site where you will be able to pay for your item.

NOTE:  If you plan on buying more items, then please do so first before completing your checkout or you will not be able to receive the automated Multi-Item Shipping Discount.
 

Sales Tax: 7.75% Sales Tax Charged to all shipments within the state of CALIFORNIA

PAYMENTS

PayPal: PayPal is our preferred payment method! Your payment confirmation will reach us in the shortest time and get your item on its way usually within 24 hours.
Money Order/Cashiers Checks: We gladly accept all money orders and cashiers checks from U.S. and Canadian banks. In most cases your item will be shipped within 24 hours of receipt of payment.
Personal Check: We gladly accept personal checks from U.S. banks. Please be aware that all personal checks require a minimum 10 day waiting period to allow for them to clear our bank.
Credit Cards: Our Channel Advisor checkout system will securely process your credit card transaction.
Note: Checks and Money Orders should be made out to: Auto Body Depot c/o eBay Sales, 6695 Rasha St., San Diego CA 92121. They must have the eBay item numbers on them in order to process and ship your order.(International money orders/cashiers checks are not accepted)

RETURNS

100% Satisfaction Guaranteed: If you are not satisfied with your purchase from TCP GLOBAL, return it to us within 30 days of receipt of your order for a full refund (less original shipping charges).

To return an item, an RGA (Returned Goods Authorization) number is required. Call us at 858-909-2110 or email us at returns@tcpglobal.com to obtain this number before shipping your item back. Send back your return via the Post Office, UPS or other service with a copy of the original order. Returned items must be in original (new) condition, with associated packing materials and packaging. Customers are responsible for return shipping costs. See your TCP Global Invoice for more information regarding returns policy. Please note that returns made without a Return Authorization Number cannot be processed and will not be accepted. Once the product is received at our warehouse we will issue a refund for the merchandise amount. We cannot refund original shipping charges. Please allow 2 weeks from receipt of your return for the credit to appear on the same account you used for purchase.

Specific Product Return Exceptions: Videos and DVDs are not returnable – if defective or damaged they will only be replaced. We must have Picture Documentation of Damage sent or emailed to us on all Paint related items (Liquid Paint, Pearls, and Metal Flakes) in order to authorize a RGA number. Do not return paint via U.S. Mail.