This lot of 15 - 5 gal pails of our white elastomeric roof coating is

$1,020.00

We ship DIRECTLY  from one of our  factory distribution centers

*Kimberton, PA *Huntington Park, CA *Elk Grove, CA *Kingman, AZ *Garland, TX

*Bartow, FL, *Indianapolis, IN, *Auburn, WA

We have both 5 gal and 55 gal Drums available for shipment, over 100,000 gallons available at all our centers

PLEASE PROVIDE A DAYTIME DELIVERY PHONE NUMBER OR THE TRUCK LINE CANNOT DELIVER YOUR ORDER!!

These 15 pails, 75 gallons will cover about 7,500 square feet one coat or 3,750 square feet 2 coats for proper manufacturer's recommendation and to be considered under warranty application guidelines.  Coverage can depend in part on your application techniques, weather conditions as well as your roof condition 

We can sell you 15 to 400 or more units of 5 gal pails of this top quality Henry Solarfex 7 year warranty elastomeric WHITE rubberized roof coatings or other special units or pallet sizes. We also have 55  gal professional drums, CALL or email for your delivered prices on ANY SIZE ORDER!!! 

 Contact us via email  to determine your freight rate. Please provide your shipping address, city, state and zip code and if the product is being delivered to a commercial address with a loading facility or to a residential location. This is VERY important information that is necessary to determine the best freight rate for your order. 

 Check out my other items!

  Specification A 1996
RPU Roof Coating 
As manufactured by Henry Company or equal  287 Solarflex Acrylic Coating System   Features Seamless -flexible rubber membrane
UL-790 Class A
Weather resistant-corrosion resistant   General Conditions This specification is valid for reroofing over most existing sound roofs, whether painted or unpainted, including materials such as metal, wood, concrete, EPDM and masonry.   Priming Requirements All bare non ferrous metal must be primed with roof primers as required.  If rust is present, RUST STOP must be used.  Painted metal surfaces need to be primed with EPOXY COAT after proper preparation. All other surfaces, whether wood, concrete, EPDM, or other material must be properly cleaned and prepared, most commonly with a high pressure water wash. Priming is most commonly not required on these surfaces.   Application Method Preparation All metal surfaces are to be power washed as required, then let to dry.  All rusted areas primed with RUST STOP, then apply appropriate primers for metal type.  Weakened or deteriorated metal must be replaced. Replace missing fasteners, tighten all loose fasteners.  Apply caulk to fasteners for proper seal.  Other surfaces need to be prepared in a like manner if applicable. For a 10 year expected roof life, use polyester felt as an interply membrane between 2 15 mil coatings on flat or smooth roof areas. On metal roofs, and roofs with irregular surface surfaces, apply a 6" strip of Polyester felt at all joint or lap areas by applying a coating of Anjon Acrylic coating and then imbedding the felt in the coating while still wet. Apply finish coat after this base coat has reached a cure. The normal application technique is by spray, though standard regular nap paint rollers may be used. Spray equipment used can be either airless or conventional spray equipment. Standard Airless Spray equipment minimums are: Pump Ratio - 30:1, Tip Size - 0.020 to 0.030 inch, Fan Angle - 60% to 80%, Hose Diameter - 3/8 inch (high compression). Application suggested method is to apply 2 coats of product, waiting at least 5 to 6 hours between coats, preferably waiting 24 hours between coats to assure a proper cure before applying the second coat. Each coat shall be about 15 mils thick.Using this method, normal coverage should be about 3.4 gallons per every 100 square feet. GREY color base coat can be used as the first interply base coat, with a WHITE finish coat. Cleanup is suggested to be done as soon as application is complete, using clean water to clean sprayer and other application tools.   Appications Guidelines 1. DO NOT store material at temperatures below 45 degrees F. 2. DO NOT apply product when ambient air temperature drops below 50 degrees F. Temperature must remain above 50 degrees F for a least 12 hours after application of product. 3. DO NOT apply over wet substrates or when inclement weather is imminent. 4. As a characteristic of all acrylics, this system is not recommended for use over cold storage installations and roofing of areas with long term standing water.    Click here for MSDS Sheets, Technical Data Sheets and Specification Data Sheets   Email us for any additional information or if we may assist you in combining freight charges