3 TINY~ROSE BUDS ~Polymer Clay Push Mold ~Handmade

Handmade

Very Pretty

3 Tiny Rose Buds

Rose measures approx-1/4"

 Polymer Clay Push Mold

Great for all your Polymer clay(Sculpey,Fimo Etc)

Also great for Paper Pulp molds etc.

Use for scrapbooking,Ornaments,Tags etc.

I will gladly Combine shipping to save you money.

My Low starting price in no way reflects the quality of my Merchandise.

I just want to give evreybody a chance to bid!!
If You have No Feedback or more than 4 negative,E-mail me before bidding,Please!I reserve the right to cancel your bid if you have No feedback or Negative feedback!
DONT BID IF YOUR NOT GOING TO PAY!
NEGATIVE FEEDBACK WILL BE GIVEN FOR NON-PAYING BIDDERS!!
Please take note of shipping charges,they are not negotiable.
I am very fair on the shipping and Handling.





  Thanks for stopping by,While your here,take a Look at my other Auctions,I am always adding New items.


I WILL GLADLY COMBINE SHIPPING IF THE AUCTIONS ARE WITHIN 4 DAYS OF EACH OTHER


 

All Questions should be asked before Bidding

(No question is too small or Silly)

Once you Bid and Win the item,It is Yours.

IF you Do Not complete the transcation,Nessasary action will be taken.

Thank you!

Thanks for stopping by,While your here,take a Look at my other Auctions,I am always adding New items.

HAVE A GREAT DAY!

Come Back Again Soon!

 

 

 

SquareTrade © AP6.0

I decided to take the time to write a short guide on how to use the Polymer Clay molds. This will help New users learn how to use the Clay Push molds and hopefully some tips for the experianced users. 1.What are Push Molds? Castings made with Polymer clay of many diffrent detailed impressions,that can be used to make your own creative designs that allow even the very begginner to make pieces that look like it took you hours to make. 2.How do I prevent the clay from sticking to the mold? Always lightly dust the mold with Baby Powder before making impression. If it does get stuck,try putting the mold with the clay in it into the freezer for 2-3 minutes to help its release. Over time Lots of use, the mold may develop a sticky residue,You can clean them by using rubbing alcohol. 3.How do I start making the designs and removing clay from the molds? Always use softened clay..Can softened by hand or use a Pasta Machine to soften and condition clay. Clay should feel like smooth Firm Putty If you are using a deep mold ,form your clay into a sharp point or teardrop and press the point of the clay into the deepest part of the mold first then fill the mold from the center out. I reccomend filling all molds from the center to the outter edge. Fill enough to edges to have someting to hold onto to pull clay out of mold.Use a Sharp craft knife to trim off any excess. DEEPER IMPRESSIONS SHOULD BE LIFTED STRAIGHT UP TO PREVENT DISTORTION.YOU CAN LEAVE EXCESS CLAY ON THE BACKSIDE TO USE AS A HANDLE,LET IT REST FOR 10-15 TO FIRM UP A BIT,THEN TRIM OFF ACCESS WITH A SHARP CRAFT KNIFE. After molding use a soft brush to remove excess powder. 4.Time to bake Bake pieces according to Clay Manufacturers instructions. You can use Colored Clay or White Clay for your projects..There are many diffrent types of paints and powders you can use on the finished baked pieces. I will add more info as I get it about various aspects of using the clay.There are also many books available at your local craft stores. I hope this Basic Guide has been of some help to you.. Please feel free to ask any further questions you may have.. Good Luck and most of all have FUN! ~DDESIGNSBYRENEE

I decided to take the time to write a short guide on how to use the Polymer Clay molds. This will help New users learn how to use the Clay Push molds and hopefully some tips for the experianced users. 1.What are Push Molds? Castings made with Polymer clay of many diffrent detailed impressions,that can be used to make your own creative designs that allow even the very begginner to make pieces that look like it took you hours to make. 2.How do I prevent the clay from sticking to the mold? Always lightly dust the mold with Baby Powder before making impression. If it does get stuck,try putting the mold with the clay in it into the freezer for 2-3 minutes to help its release. Over time Lots of use, the mold may develop a sticky residue,You can clean them by using rubbing alcohol. 3.How do I start making the designs and removing clay from the molds? Always use softened clay..Can softened by hand or use a Pasta Machine to soften and condition clay. Clay should feel like smooth Firm Putty If you are using a deep mold ,form your clay into a sharp point or teardrop and press the point of the clay into the deepest part of the mold first then fill the mold from the center out. I reccomend filling all molds from the center to the outter edge. Fill enough to edges to have someting to hold onto to pull clay out of mold.Use a Sharp craft knife to trim off any excess. DEEPER IMPRESSIONS SHOULD BE LIFTED STRAIGHT UP TO PREVENT DISTORTION.YOU CAN LEAVE EXCESS CLAY ON THE BACKSIDE TO USE AS A HANDLE,LET IT REST FOR 10-15 TO FIRM UP A BIT,THEN TRIM OFF ACCESS WITH A SHARP CRAFT KNIFE. After molding use a soft brush to remove excess powder. 4.Time to bake Bake pieces according to Clay Manufacturers instructions. You can use Colored Clay or White Clay for your projects..There are many diffrent types of paints and powders you can use on the finished baked pieces. I will add more info as I get it about various aspects of using the clay.There are also many books available at your local craft stores. I hope this Basic Guide has been of some help to you.. Please feel free to ask any further questions you may have.. Good Luck and most of all have FUN! ~DDESIGNSBYRENEE~

Powered by eBay Turbo Lister
The free listing tool. List your items fast and easy and manage your active items.