AIR-ZONE® PROFESSIONAL 14,000 mg PRO OZONE GENERATOR!

The Air-Zone® XT-14000 features 12 individual 24 carat gold plated in our United States Patented ozone elements each with it's own electronically protected transformer.

Old style mica ozone "plates" consist of flimsy, easily corroded, steel screens

This cellular construction makes it easy to remove, clean, or replace each element as needed.
The LED display on the control panel lets the user know the working status of each circuit at all times.

Old style ozone "plates" consist of flimsy, easily corroded, steel screens

They create no Nitrogen Oxides like old style ozone "plates".
These United States Patented ozone elements can be easily be taken out for cleaning or replacement.
Each element comes apart and can be cleaned in less than a minute.

We DO NOT use cheap MICA plates in our ozone generators.

MICA is the cheapest and worst material to use in an ozone plate. It easily breaks, flakes apart, burns, and shorts out the generator. 
Stay far away from any ozone generator using a MICA ozone plate.

Any of the ozone switches A, B, & C can be on at any time choosing an ozone output of either 9300, 18,600, or 28,000 mg.hr. in any combination.

Old style ozone "plates" consist of  flimsy easily corroded steel screens and delicate thin pieces of glass or mica which must ALWAYS be in perfect alignment.
If not cleaned and aligned constantly, old style ozone "plates" will produce less ozone, and possibly even spark out dangerous high voltage electricity.

Old style ozone "plates", first designed in the 1800's,  must be removed, scrubbed clean, dried, and be meticulously reassembled, or they will not work correctly. Even with all that work, their life span is notoriously short.

A 10,000 mg/hr "old style plate" type unit would contain 40 different parts, in 10 separate holders, that ALL must be kept in perfect alignment, or they will not work correctly. 

The built in Countdown Timer on the XT-14000 allows the unit to be run from 1 hour up to 24 hours.  The timer is easily set or reset with just a press of a button.
The machine can also be used in the continuous mode without using the timer.

Air-Zone® uses completely sealed, high voltage transformers, that can withstand abuse before shorting out. They are designed specifically for our ozone generators.  Combined with our innovative ozone element design, it is very rare that one of our power transformers blow out.

Competitors use off the rack, open iron core transformers. The exposed iron can quickly rust and deteriorate. These types of transformers are not specifically designed for use in an ozone generator, and have a hard time maintaining a long life span in this type of machine.

Some companies use the same exact transformer in many different sized models.

Air-Zone® uses multiple transformers in our different models.  How can a single transformer that is used in a small ozone machine be expected to handle the much higher load in a large ozone generator?

Many competitors machines simply use ONE transformer, the SAME EXACT transformer in many of their different low and high ozone output generator models.

Whether it be a single plate 1000 mg/hr model, a 5 plate 3600 mg/hr model, a 5 plate 5000 mg/hr model, or a 10 plate 10000 mg/hr model, some manufacturers use the same exact transformer in every machine.

How can the SAME transformer that is expected to handle one high voltage ozone element, handle ten high voltage ozone elements?

If a competitor states "Our transformer is so good we can use the same one in our low powered model as our high powered model" then what justifies the huge jump in price between the low and high powered models?
It seems to us they are just charging the customers empty dollars of more and more profits for increased ozone power.

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed. The load on the transformer HAS to be radically different on a single or five plate ozone generator. 

This is proven by the fact that when a competitor adds 4 more ozone plates to a 1000 mg/hr machine that the total ozone output does NOT equal 5000 mg/hr.

The "upgraded" generator now only puts out 3600 mg/hr, the missing 1400 mg/hr of ozone output has been lost because the transformer has a hard time handling the different load.

That proves that the load is radically different when you simply add more ozone plates to a power transformer.  If the transformer has been strained so that it looses that much ozone power, then it can be concluded it is that much closer to straining and blowing out. 
It has to run at a higher temperature. 

So if competitors ozone plates are as cheap in cost as they say, and they use the same transformer in a 1000 mg/hr machine AND the 10,000 mg/hr machine, what justifies the more than $700.00 cost difference between the two models?

Our XT-2000 uses a single transformer. The XT-4000 uses 2 transformers. The XT-6000 uses 3 power transformers.  Our XT-14000 uses 6 power transformers and our XT-28000 uses 12 separate transformers.

We do this because to present a balanced load, and to have even power distribution. 
It is better to use multiple transformers when doubling or tripling the ozone power.
It only makes good sense. It makes for a more balanced ozone machine.

We don't just add two more ozone elements to the XT-2000 to make it a 4000 mg/hr machine.
The XT-4000 uses 2 separate transformers. Simply adding ozone elements isn't the proper solution.  Adding 2 more elements would NOT equal 4000 mg/hr. It might only increase the ozone power to 3200 mg/hr because the load presented to the transformer would be completely different.

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed. The load on the transformer HAS to be radically different on a single or five plate ozone generator.

Keep in mind the fact that competitors also use ozone plate technology where each "plate" has 3 pieces in it that can easily move around.  They use a spring system to keep each part of the plate in perfect alignment. A 10 plate, 10,000 mg/hr ozone machine will have 30 separate pieces in its 10 ozone plates!  A 10,000 mg/hr "plate type" ozone machine has 30 parts that must ALWAYS be in perfect alignment or disaster will occur.

If a single piece of the glass or mica non-conductor breaks, cracks, or just slips out of alignment due to a lack of spring tension, then the electrical conductor, screen parts of the ozone elements can arc and cause an electrical short. 
When an ozone plate short outs, the transformer is also shorted out.  No matter how well it is built, a transformer cannot stand being shorted out for very long.  Electrical transformers cannot stand to have a high voltage, zero ohm load on them for very long without being put under a huge amount of strain.

Air-Zone® not only uses multiple transformers in our higher powered units to help balance the load, they also use our U.S. patented ozone elements which do not have components in them that can move, or shift out of alignment. 
There is no way for them to short out as standard ozone plates can.

Don't buy the argument that using multiple transformers gives a machine more to break down. 
The truth is if properly sized transformers are used and not strained to capacity, there is very little change they will blow out.  Simply adding ozone plates as other manufacturers do, is what overloads electrical transformers and makes them more likely to blow out.

Air-Zone® are simply more stable ozone generators than most other brands.
Electronic protection circuits and fuses prevent our internal components from overload & burnout.

They keep the inside of the unit dust free so that the ozone output does not drop as in many other types of ozone generators.

This can be useful because sometimes a room can actually run out of oxygen if it has all been turned into ozone.

By connecting the machine to a "clean air draw" more ozone can be produced if needed.

After 30 minutes, at a distance of 12 feet the ozone level reached 8 parts per million.

This is the type of power required to kill mold and bacteria.

Rated Ozone Output:  4500, 9000, or 14000 mg/hr
ACTUAL OZONE OUTPUT: 14,500 mg/hr
(ozone output verified by Société Générale de Surveillance)
Our Ozone outputs are rated in HIGH HUMIDITY environments.
High Voltage Transformer Output: 5000 Volts
Heavy Duty Fan with precision ball bearings
Ozone Air Flow rate:  180 CFM
Built in Timer: From 1 hour to 24 hours plus continuous setting
Electrical Source:  AC 115 Volts, 60 Hz 
Available in 220 Volts as a special order
1A, 2A and 6A Protection Fuses
Electrical Consumption: 0.9-1.9 Amps, 110 -230 Watts.
Dimensions: 26.27" ( L ) X 13.78" ( W ) X 9.05" ( H )
Actual weight: 33 lb., Shipping weight 45 lb..
Five Year Warranty

If you win this auction you are obligated, by a legal contract, to pay for it.
If you do not pay for it you will be reported to eBay, and will recieve negative feedback.

EVERY negative feedback that we have ever recieved is from customers who in some way refused to pay for the item they won, or who refuse to follow the simple instructions that we require like giving us a proper persons name, shipping address, and a phone number.

A phone number is REQUIRED by Fedex to insure the shipment, and we will NOT ship without insuring your item.