RC & ME Hobbies
rcandme.com
is proud to offer:
100% professionally Built, configured and tested T-Rex 600CF by Our AMA certified trainer and Pro Builder.
You will get the following:
1. a T-Rex 600ESP, with 100A esc, 650 Brushless motor, BEC, BEC battery.
2. A Futaba 7c 2.4 radio system with 617 RX and 3 x 3152 servos (3152 Digital servos will be used for cyclic control)
3. A Futaba 401 Gyro and matching 9254 digital High speed servo
4. A set of 600MM CF main blades
5. A 6C 22v 25C discharge 5000mah pro li-po battery
6. Bantam BC6DC Li-Po Charger.
*** Our pro builder will completely build the heli, install the electronics, set-up the radio and configure the entire system. Once done, the heli will be taken and test flown, adjusted as needed till perfect and packaged for a safe trip to you.
*** Why gamble on buying a complete system from overseas when you can get local USA support by RC & ME?
T-REX 600 ESP Kit Combo (BLACK) KX016008A
This is the Newly redesigned Trex 600E kit. Just like the Trex 600 Nitro Super Pro This kit includes all the upgrade metal parts as well as the new 650L motor!
Some key features in the redesign are the new Frames with new servo locations for enhanced geometry. Also included in this kit is the new swash plate and new elevator arm that doubles as an anti rotation bracket.
Specification:
Length:1160mm(45.67 in)
Height:400mm(15.75 in)
Main Blade Length:600mm
Main Rotor Diameter:1350mm(53.15 in)
Tail Rotor:240mm(9.45 in)
Motor Drive Gear:14T(15T optional)
Main Drive Gear:170T
Autorotation Tail Drive Gear:180T
Tail Drive Gear:40T
Drive Gear Ratio:1:12.14:4.5/1:11.33:4.5
Weight(w/o main blade):2450g(5.4 lbs)
Flying Weight:Approx 3300g(7.3 lbs)
Color carton:64.8x28.7x11.3cm
Outer carton:66.5x58.5x36.5cm ,6sets/ctn
Accessories:
T-REX 600ESP Kits set
600D Carbon fiber blade Set
Fiberglass canopy
Standard Landing skid
RCE-BL100G 100A Brushless ESC(Govener Mode)
650L Brushless motor
REC-B6X External BEC
5.1V Two-way step-down voltage regulator
Li-Polymer 7.4V 1900mAh 18C For BEC
Futaba 7C 7-Channel 2.4GHz Heli/4 S3152 Servos
This is the Futaba 7C 2.4GHz Helicopter Radio System
with the R617FS FASST 7-Channel Receiver,
and S3152 Digital High-Torque Servos.
This is the helicopter version which will default to heli settings
when powered up and does not have a ratcheted throttle stick.
Modeler can change from the default mode (mode 2 in USA) by holding the
Mode and End keys and then turning transmitter On to access the STK feature,
changing mode and turning transmitter Off and then On again.
It is recommended to send transmitter to the Futaba Service Center
to change switch operation.
FEATURES: Futaba's FASST (Futaba Advanced Spread Spectrum Technology) shifts
very quickly virtually eliminating signal conficts and
interruptions unlike other 2.4GHz systems that only stay on one
or two frequencies
Dual antenna diversity enables FASST system to automatically and
seamlessly select the best reception between the two antennas
built into the receiver ensuring that the aircraft stays under
constant control of transmitter regardless of altitude
Newly designed Dial-N-Key jog dial with joy stick button allows
cursor movement in four directions for very user friendly
navigating through menus and programming
Futaba GY401 Gyro w/S9254 Digital Servo
This is the Futaba GY401 Gyro with an S9254 Digital Servo.
This is a high performance, compact and lightweight
(AVCS) Angular Vector Control System gyro developed for model helicopters.
Because the sensor and control circuit are integrated, it is simple to install.
FEATURES: AVCS System: Since the rudder trim changes (caused by wind and other
meteorological changes) the front, rear, and other heli attitudes
change and are automatically cancelled; tail (rudder) operation is
easy, making it perfect for 3D flight.
(also known as heading hold gyro)
SMM Gyro Sensor: Use of this newly developed technology virtually
eliminates rudder trim changes during flight (see COMMENTS).
Digital Servo Compatible (DS Mode): DS mode makes it compatible with
Futaba Digital Servos. This maximizes the high-speed response
performance of the Digital Servo.
Included high-speed S9254 Digital Servo boasts 47 oz-in torque and a
speed of .06 sec/60°
Remote Gain Function and Mode Switching Function Remote: Gain
function allows sensitivity switching from the transmitter and mode
switching function allows AVCS/normal gyro mode switching.
Integrated, compact and lightweight design made possible by high
density mounting technology.
Conductive Resin Case: This case improves EMC (Electrostatic and
electromagnetic interference) resistance.
One year warranty
INCLUDES: One GY401 gyro
One S9254 Digital servo, available separately
One .81" (20.5mm) round servo horn, one 1.8" (45mm) round servo horn
one 1.25" (32mm) 6 point servo horn, one 1.5" (39mm) 4 point horn,
mounting hardware
One mini plastic adjustment screwdriver
Three mounting pads
One instruction sheet
Bantam e-Station BC6DC Lipo Balancing Charger
| Specifications: |
| Operating voltage |
DC 11~18 volts |
| Idling current |
approx. 100mA |
| Charge/discharge power |
max. 80/8W |
| NiCd/MH |
1~15 cells |
| LiIo/LiPo/LiFe |
1~6 series |
| Pb |
2~20V |
| Charge current |
0.1 to 5.0A |
| Discharg current |
0.1 to 1.0A |
| No. of cycle |
1 to 5 times |
| Battery data memory |
up to 5 data |
| Weight |
340g |
| Dimension |
130x90x30 mm |
Thunderpower or Flightpower 22.2v 5000Mah 25-28c Li-Po battery and Bantam BC6DC Charger
You will receive a 5000mah li-po, one of the best batteries on the market to provide all the power neeeded
for basic flight to full out 3D.
Every helicopter will be fully tested, trimmed and double checked prior to shipping.
Once ready, they will be packaged with care, packed in a 48x16x16 box and shipped completly ready for you to fly.
Please let us know how you would like the heli to be programmed.
1. Basic, no 3D
2. Basic and Basic 3D
3. Full out 3D.
Heli kits can be customized, please contact us for more info.
Back to Search Results
) 
RC-and-ME
Print
Report item
and your 