SquareTrade ? AP6.0

Product Condition    You Are Buying A *Brand New* Item.  NEW CROWN XTI2000 2 CHANNEL POWER AMPLIFIER AMP XTI-2000

Store Policy: A Paypal payment can only be accepted with a Confirmed Shipping Address. (a confirmed address can only be the Billing address of a credit/debit card/bank account; we only ship to Billing Addresses) If a paypal payment is received with an unconfirmed shipping address, it will be refunded; so please read our policy for more information! Buyers are responsible to provide a confirmed billing address on a paypal payment and are responsible to read our policy. We only ship to billing addresses if payment is received on paypal or over the phone. PO Box addresses are not accepted !! International Buyers (Canada, UK.): Must Call UPS (1800)263-8125 for the Cost of Border Charges Due to the Transfer Over the Border. We do not Charge or Collect Border Fees, UPS Does Upon Delivery!! Please Click on The Link Below to READ our Store Policy Before Purchase.  By clicking "Buy It Now", you place an order & agree to follow our Store Policy.   (Click to Read our Store Policy)  - Store Policy

We are Proud of our Fast Shipping !!

Contact Us Monday through Thursday: 10:00 am to 6:00 pm EST. Friday: 10:00 am to 4:30 pm EST No Weekend Hours. Phone: 718-331-1818  E-Mail: UGotADeal@OptOnline.Net

Specifications:  1,000W/ch @ 2 ohms, 800W/ch @ 4 ohms, 475W/ch @ 8 ohms, 2,000W bridged mono @ 4 ohms, 1,600W bridged mono @ 8 ohms. Voltage Gain at 1kHz, 8 ohm rated output: 32.9dB Frequency Response: ±0.25 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms Phase Response (at 1 watt, 20 Hz to 20 kHz): ±15ø Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode Sensitivity: 1.4V Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): _105 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 500 Hz. Crosstalk: > 80 dB below rated power, 20 Hz to 1 kHz. Common Mode Rejection (CMR): > 45 dB from 20 Hz to 1 kHz._Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V _50/60 Hz AC Line Current: 6.9A At Idle: Draws no more than 90 watts. Operating Temperature: 0ø C to 40ø C at 95% relative humidity (non-condensing). DSP Section EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel Delay: For signal alignment of driver; 5 mS total delay Subharmonic Synthesizer: Adds low-frequency content Output limiter: Prevents clipping Presets: 10 user speaker presets Front Panel Controls and Indicators Level: Detented rotary level control, one per channel Power Switch: On/off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen are used to access menu items LCD Screen: Backlit liquid crystal display shows speaker presets Signal Indicator: Green LED, one per channel, flashes when a very low-level signal is present at input 10 Indicator: Green LED flashes when output signal exceeds 10 dB below clip. 20 Indicator: Green LED flashes when output signal level exceeds 20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Rear Panel Controls and Connectors AC Line Connector: NEMA 5-15P (15A) Input Connector: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking