 
|
COMPLETE HYDROGEN Generator KIT with Dual Map Sensor Enhancer & PWM |
|
|
 |
DESCRIPTION | |
THIS AUCTION IS FOR A COMPLETE HIGH QUALITY HEAVY DUTY HYDROGEN GENERATOR KIT. THIS IS THE BEST ON EBAY AND THIS IS READY TO BE SHIPPED TO YOU. I HAVE JUST PRE WIRED THE GENERATOR, SOLENOID, RELAY & FUSE FOR EASY INSTALLATION. HYDRO GENERATOR ARE MADE of 10 PLATES OF STAINLESS STEEL in H2OReactor's H-Silo Container. Open Bath HHO cell/Hydrogen Generator. See-through Clear Acrylic container that you can admire your cells while producing hho gas. A container that you can check and verify that all of your cells are running and functioning properly, unlike some container that you CAN NOT even see and verify if the plates are shorted or not. Shorted cells doesn’t generate hho gas, it does produce heat and draws more current as wasted energy and will boil your electrolyte, or worst, it will melt your container. Removable top cover, gasketized for air tight seal. You can open and study how this cell works, reconfigure it, replace it with your own desired plates. The Container is made of acrylic and has a high melting point of 266°F/130°C, compared to PVC which melts at 176°F/80°C. The acrylics are bonded using solvent welding by melting the acrylic then bonding it together as one single piece. No expoxy, No marine glue, Not even a silicone glue, since all of this will poison your electrolyte and produce foaming bubbles. SPECS:
1/4″ Thick Clear Acrylic, Cover, Flange and Bottom
1/8″ Thick Clear Acrylic tube.
4.25″ Inside Diameter acrylic tube.
8.5″ Tall
Bonded together using Acrylic Solvent Welding, no glue or epoxy.
Removable cover with EPDM Sealing Gasket.
Refill Cap with Safety Blow-off membrane
1/4″ NPT Threaded, with 1/4″ barbed fitting.
1/4″ Stainless threaded rod power terminals with wing nuts
1/4″ SS316 Lock Washers on Power terminals
1/4″ SS316 Hex Nuts on Power Terminals
1/4″ SS316 Washer on Power Terminals
1/4″ Zinc Plated Neoprene Bonded Sealing Washer
Cover Screws/Washers/Nuts.
266°F/130°C Acrylic Melting Point. PVC actually melts at 176°F/80°C.
This container has a safety blow-off membrane, it's your last line of defense
THIS IS A GREAT SET-UP AND IT REALLY PRODUCES HHO GAS WELL, 2-4+ Liters Per Minute... I HAVE JUST INCLUDED A GAS/WATER FLOW METER SO YOU WILL KNOW EXACTLY...MUCH MUCH BETTER THAN ANY OTHER ONES. WHEN SET UP CORRECTLY OUR TRUCK RAN 90% HHO GAS...THIS UNIT IS 10" tall and 6" round-wide and 6" deep...I WENT THE EXTRA MILE TO MAKE SURE YOU HAVE EVERYTHING YOU WILL NEED TO INSTALL IN YOUR VEHICLE INCLUDING GAUGES TO VERIFY & CHECK WHAT EXACTLY IS HAPPENING, Just ADDED A DIGITAL MULTI-TESTER(Not In The Picture) AND AN ADJUSTABLE WATER FLOW METER. I HAVE PUT A FILL HOLE WITH CAP ON THE TOP OF EACH CELL FOR EASY-QUICK FILL..Also...INCLUDING AN ADJUSTABLE PWM AND A TOTAL CONTROL OF YOUR GENERATORS, ALSO WITH A DUAL MAP SENSOR ENHANCER PLUS A PCV ENHANCER, CHECK VALVE & FLAME ARRESTOR. What about winter time, well in the winter time you have to modify your unit to contain glycol (green antifreeze). THIS DOES WORK FOR ANYBODY. THIS WILL WORK ON ANY LARGER CARS, TRUCKS AND DIESEL and that is a big yes it is Very Effective in Diesel Vehicles, Semi Trucks etc. THIS SYSTEM DOES NOT have a bubbler and this is what sets my system apart from the others. A bubbler is made and used for a few reasons it is simply used to help remove water vapor from the HHO and provide some level of protection during a flashback. In my system I use a air water seperator which helps to seperate the water from the hho. And when there is water in the seperator you can remove it by simply opening the valve and letting the water out. In a semi it is rare for a flashback or misfire. But in anyway you look at it its more effective at its job. I HAVE INCLUDED A WATER SEPERATOR and the FLASHBACK DEVICE AND a CHECK VALVE. The end result though is a better quality product.(Retail Value of This Package $999.99.) My Partner INSTALLS these locally here...
INCLUDED IN THE AUCTION:
1- HYDROGEN GENERATORS-10 PLATES STAINLESS STEEL
1- DUAL ADJUSTABLE PWM (Pulse Width Modulator)
1- 7 FUCTION DIGITAL MULTI-TESTER
2- OXYGEN SENSOR EXTENDERS
1- GAS/LIQUID CHECK VALVE, FLASH BACK Protector
1- DUAL MAP SENSOR ENHANCER.
1- Heavy Duty BUBBLER or Water Separator(NOT shown in Picture)
1-TABLESPOON OF 100% LYE(Much Better Than Baking Soda)
1- FLAME ARRESTOR
1-30amp INLINE FUSE HOLDER AND FUSE
1-30/40 Amp RELAY
1- RED AND BLACK
2- EXTRA VACUUM HOSES (48"Each) TO CONNECT TO PCV VACUUM LINE
1- FUEL LINE TO CONNECT TO VEHICLE + (24") PLUS 1- (24") CLEAR HOSE TO CONNECT THE UNITS TOGETHER
1- VACUUM T CONNECTOR
2 -BUTT SPLICES, 2- QUICK SPLICE CONNECTORS
4 -RING TERMINALS
4- HOSE CLAMPS
1- 12 Volt CONTINOUS DUTY SOLENOID
1- BONUS CD WITH EVERYTHING YOU NEED TO KNOW ABOUT HYDROGEN
1- COMPLETE GENERATOR INSTALLATION INSTRUCTION MANUAL
1-DUAL MAP ENHANCER INSTALLATION INSTRUCTION MANUAL
1 -MAINTENANCE AND TROUBLESHOOTING MANUAL
I AM USING THESE IN MY AUTOMOBILES. I HAVE BEEN EXPERIMENTING WITH THIS SYSTEM FOR OVER 2 YEARS NOW AND HAVE FOUND OUT A LOT. THIS IS A KIT DESIGNED FOR ANY WORKING VEHICLES Where a Smaller hho generator will not give the driver as much as needed. THIS SHOULD FIT NICELY IN MOST ALL CARS & TRUCKS, INCLUDING SEMIS...I PERSONALLY KNOW MY VEHICLE (2005 Ford Ranger) RUNS MUCH BETTER WITH THIS SYSTEM. SAFETY: I HAVE INCLUDED THE FLASHBACK ARRESTOR, A CHECK VALVE AND A WATER SEPARATOR SO THAT THIS WILL BE TOTALLY SAFE FROM WATER GOING INTO YOUR MOTOR AND ALSO STOP ANY HEAT...THIS Fuel Cell is made from 10 STAINLESS STEEL PLATES for more HHO, All of this cell is made from High QUALITY Grade STAINLESS for Maximum Durability and Long Life. THIS CELL IS MADE OF 10- 316 b Stainless Steel Plates each plate is secured using nylon screws and nylon nuts. this also has no wires inside of the generator current is passed through stainless steel nuts and screws. Plates are +-+-+-. If you have or want a different plate set up just ask I will comply to most of your needs. You WILL USE THE PWM in which you can branch off to power the two generators as you will want to keep the voltage at 30 amps. TRUE 30Amp PWM (Pulse Width Modulator) with ADJUSTABLE Frequency PWM for hydrogen generator. This unit improves the efficiency of your hydrogen cell by allowing to control the temperature and current going to your hydrogen cell. New Heavy Duty design PWM with new features providing better performance over almost any other units for sale on eBay.
Now in purchasing this kit I assume that you have some basic automotive knowledge and can do some basic trouble shooting and work through issues. The most common issue I have had to help my customers work through is blowing fuses as any hydrogen generating unit heats up it will start to draw more energy and overheat. You have to try to keep your HHO system running at 30 amps. Each unit is checked and ran before the unit ships out. I will also do the best I can to help you with any situations tat you run into. Some of the common questions I have been asked are #1 how much hho does this kit produce. Well my answer is this I do not test each unit for how much hho is produced. The reason is this simply it takes too much time to test every unit. YOU Will ALSO GET A NEW H20/GAS FLOW METER TO KNOW FOR YOURSELF. This ALSO comes with CONTINUOUS SOLENOIDS / RELAY That does the job and handle 80amps. THIS ALSO Comes with a 12 VOLT CONTINUOUS DUTY SOLENOID. SIMPLE TO HOOK UP, POSITIVE AND GROUND ARE THE TWO ON THE SIDE AND THE 2 SMALLER CENTER ARE FOR GENERATOR or ACCESSORIES, VERY SIMPLE INSTALLATION that takes less than an hour but due to each car's individual needs I am including a universal mount. I am also including a installation guide with directions on how to install this device. Also an Installation guide for your Map Sensor Enhancer. This system has been built to beyond Water 4 Gas specification. The cell is stainless steel and has no wires of any kind inside the cell. The cell is perfect for Larger cars and Trucks and Semis. This unit will need distilled water and 1/2 Teaspoon of baking soda or an electrolyte of your choice to produce the hydrogen. Always leave about 1 to 1.5 inches of air space in the top of the generator. The generator is very strong and durable. This design is much safer than the original wire designs. This unit is designed for a 12-volt system. Positive and Negative can be located on either side of the cell doesnt make any difference which. Dont Settle for second best generators like wire or screen designs that can rust away or short out. The soulution will turn brown after a week or two of use, this is normal but can be kept to a minimal by using distilled water and less electrolyte. My generators are built solid and made to last and be durable. I recomend installing a Flashback Arrestor (Included) with this unit to prevent any sparks from reaching the unit. This unit should never be ran above 12 amps, this will damage the unit or cause failure from extreme heat. They are all custom built to the same spec...but may vary. I use the picture of Exacltly What YOU are GETTING. 1 gallon of water provides 1833 gallons of gas! Will operate on any internal combustion engine, diesels included. All bolts and nuts are Stainless Steel. The use of stainless nuts and bolts means there are no metal parts inside to rust. The nuts and bolts holding the plates together are nylon. The plates have been electrically treated for higher hydrogen production and longer life. When you purchase one of our units you can expect increases in fuel mileage from 30%-95% depending on your application.and smoother acceleration and increased performance HHO generator run your car on clean burning HHO/brown gas!!!! and save $$$$ at the pump and reduce emissions. Hydrogen can be totally nonpolluting (water is the exhaust). I have encountered different results from different vehicles but they all increased their MPG some more than others but look at it this way if you increase by any it's less you have to pay the oil companies. In this auction you will receive the Complete Hydrogen Generator Unit and ALL Accessories. Remember all cars are road tested at 56 miles per hour with no air or accessories on , this is how the EPA judges highway MPG for new vehicles. We all know you never get what is advertise on the sticker. If they are so great why isn't the car manufactures making them already. In 2009 we will start to see the emerging technology with HONDA and Japan. So why would you think that they will not allow hydrogen boosters to be manufactured? Because of politics this whole fuel crisis is politics but now is your chance to get back at the oil companies I have been doing it for over a year and it feels Great. THIS KIT ALSO COMES WITH A CD ITSELF IS A COMPILATION OF 3,000+ PAGES OF INFORMATION OF HOW TO RUN YOUR CAR ON WATER, HYDRO. EVERYTHING YOU WILL WANT TO KNOW IS ON THIS CD, INCLUDING THE FAMOUS (WATER4GAS$97Value). This CONTAINS ALL INFO ABOUT HYDROGEN & FUEL CELLS, Electrolytic Hydrogen Production , ALSO Includes Hydrogen: The Fuel for the Future , Hydrogen Quick Facts , Hydrogen Use and Safety, ENGINE MANUALS, DIAGRAMS, & VIDEOS. I AM RUNNING ALL MY AUTOMOBILES ON WATER HYDRO.
HELPFUL INFO:
ALSO INCLUDED MAP SENSOR ENHANCER : IN ORDER TO ACHIEVE THE OPTIMUM MILEAGE WITH A HYDROGEN - THE FUEL INJECTION MUST BE ADJUSTED, THIS IS WHERE THE MAP (MANIFOLD ABSOLUTE PRESSURE) SENSOR ENHANCER COMES IN. ONCE THE HYDROGEN IS INTRODUCED INTO THE INTAKE MANIFOLD, THE VEHICLE'S ECM WILL SOMETIMES UPGRADE THE AMOUNT OF FUEL IT INJECTS INTO THE AIR FUEL MIXTURE DUE TO THE INCREASED PRESSURE IN THE INTAKE MANIFOLD - THIS ENHANCER ALLOWS THIS EFFECT TO BE COUNTERED, AND THE HYDROGEN WILL COMBUST IN THE CYLINDERS IN PLACE OF THE EXTRA FUEL. THIS (OBVIOUSLY) LEADS TO A SIGNIFICANT INCREASE IN MPG!!!
OXYGEN SENSOR EXTENDERS: THESE WORK IN CONJUNCTION WITH THE MAP SENSOR ENHANCER TO ADJUST THE FUEL OUTPUT TO ALLOW FOR THE INTRODUCTION OF HYDROGEN. THESE FIT INTO THE EXHAUST UNDERNEATH THE VEHICLE'S OXYGEN SENSORS, ALLOWING THE SENSORS TO CONTINUE TO DO THEIR JOB, BUT FOOLING THEM INTO READING LESS OXYGEN IN THE EXHAUST, THUS FURTHER LEANING OUT THE AIR FUEL MIXTURE, RESULTING IN IMPROVED FUEL ECONOMY.
Also Included:
-
Detailed installation, usage, tuning, and maintenance guides, based from information provided from Water4Gas manuals. This unit produces HHO gas through electrolysis of water which is highly explosive. Caution must be exercised when using this product. We will not be held responsible for the misuse of this product. By purchasing you agree to use this product at your own risk, to use it correctly and to exercise proper safety and caution. We do not recommend the use of this product on a car without a the flame arrestor, bubbler and fuse all included...THANK-YOU...
$HOP & $AVE ONLINE FROM US...
THIS IS ALL WE DO AND WE ARE THE FASTEST SERVICE ON EBAY AND OUR FEEDBACKS PROVES IT CLICK HERE  ...ADD US TO YOUR FAVORITE SELLERS PLEASE CLICK HERE...PLUS THE POST OFFICE IS ACROSS THE STREET. WE MAIL OUT ORDERS EVERYDAY...Winning buyer pays shipping charge. We KNOW that you want the lowest shipping & handling so WE have it down to the penny just for you.
CLICK HERE FOR MORE 
WE OFFER WHOLESALE PRICES ON QUALITY NAME BRANDS, SO BID & WIN! OR BUY-IT-NOW
LOWEST PRICE ON 
DIRECTLY FROM OUR WAREHOUSE TO YOUR DOOR AT ROCK BOTTOM PRICES & FASTEST SERVICE IN THE USA...GUARANTEED
YOU WILL BE GLAD YOU DID!
|
* SHIPPING INFORMATION * |
FAST-SHIPPING...
 
WITHIN 1 MINUTE TO 6 HOURS OF PAYMENT,
WE PRINT OUT YOUR MAILING LABEL, AUTOMATICALLY USPS eMAILs YOU WITH YOUR DELIVERY CONFIRMATION AND TRACKING# AND WE MAIL YOUR ORDER AS SOON AS HUMANLY POSSIBLE...
SHIPPING: USA ONLY, USPS Shipping charge for address Within 48 STATES ONLY.
NO INTERNATIONAL SHIPPING.
Ship Method: We SHIP via US POST SERVICES ONLY with FREE Tracking Number.
TRACK YOUR ORDER HERE
Insurance is not included (optional)
|
* PAYMENT ACCEPTANCE INFORMATION * |
WE ACCEPT: PAYPAL ONLY... MAILING ADDRESS: E.J.L. - 237 S.W. 11th STREET DANIA, FLORIDA 33004...OFFICE# (954) 644-1924
SiteDesign By WebMaster of JaysUnique Corporation
Copyright © 1991-2009, All rights reserved. | | | | | |
Back to Search Results
) 
Print
Report item
and your 