SEALS AC/R LEALS & MORE

CLIPLIGHT COMPANY, simplifing A/C and Refrigeration repair

"THE NEW APPROACH FOR HARD TO FIND MICRO LEAKS"

PROFESSIONAL FORMULA

FOR RESIDENTIAL UNITS 1.5 TON or 5.3 KW and up to 5 TON.

Application:

One 3 fl oz can for systems 1.5 ton up to 5 tons.

Two 3 fl oz cans for systems greater than 5 ton and up to 25 ton.

Use only on low-pressure side.

Part# 972KIT

REPAIRS HARD TO FIND LEAKS AND CONTINUES TO CIRCULATE IN THE SYSTEM TO SEAL FUTURE LEAKS.

For professional use only: Always wear safety glasses and protective gloves

• Super Seal TOTAL 2 permanently seals micro leaks in condensers, evaporators, and lines in A/C and Refrigeration systems.
• Contains a drying agent which eliminates moisture while increasing drier efficiency, also prevents acid from forming and contains UV tracer dye to find larger leaks.
• Easily Installed in Minutes
• Seals hard to find micro leaks
• Compatible with ALL oils and refrigerants
• For use in systems 1.5 TON or larger and 30 oz. oil capacity in sump.
• Perfect for Residential Commercial or Industrial applications
• IDEAL FOR DRYING WET SYSTEMS AND SEALING MICRO LEAKS CAUSED BY FORMICARY & ACID CORROSION.
• Ideal for leaks caused my formicary (ants nest) & internal acid corrosion, vibration, and temperature variation.
• Complete one time use throw away kit
• Includes charging hose
• Use in compliance with the Montreal Protocol and Regional or Federal laws for the handling of refrigerant.




SUPER SEAL TOTAL 2™

Installation Instructions

 

Important before proceeding

 

For professional use only: Always wear safety glasses and protective gloves

Always point can bottom away from yourself when charging or injecting - Can bottom has a pressure relief valve which will release if pressure exceeds 300 Psig / 2068 KPa

Use in compliance with the Montreal Protocol and Regional or Federal laws for the handling of refrigerants

 

The system should be fully charged before injecting

SUPER SEAL TOTAL™

 

APPLICATION GUIDELINES

 

TOTAL™ 2

One 3 fl oz / 89 ml can for systems 1.5 ton / 5.3 KW up to 5 ton / 17.6 KW

Two 3 fl oz / 89 ml cans for systems greater than 5 ton / 17.6 KW and up to 25 ton / 88KW

 

INSTRUCTIONS:   clock wise = cw and counter clockwise = ccw.

 

1.  Turn off A/C unit and allow enough time for refrigerant to equalize in system.

 

2.  Confirm that can tapper piercing pin (B) is fully retracted below seating washer. Turn valve handle (A) ccw.

 

3. Thread SUPER SEAL TOTAL™ can (C) onto can-tapper (B) by turning cw. Be careful not to cross thread or over tighten.

 

4.  Thread female fitting (D) onto vacuum pump and draw vacuum for approximately 1 minute to eliminate air in tap hose.  (Where Regional and Federal laws permit you may use systems refrigerant to purge hose. Connect hose to low side charging port while unit is off and back off can from tapping valve allowing refrigerant up to the tapping valve can assembly.  Skip to step 7. 

5.  Remove female fitting (D) from vacuum pump while it is running to maintain vacuum in tap hose.  After disconnecting shut down vacuum pump.

 

6.  Thread female fitting (D) onto low side service port immediately after removing from vacuum pump.

 

7.  Turn can-tapper piercing handle (A) cw until it stops. This action pierces the can.

 

8.  Hold can upside down and above the low side service port. Turn handle (A) ccw slowly allowing the system's refrigerant to fully charge can. The can will become warm once the refrigerant mixes with its contents. Allow the can to dissipate the additional heat of charging which should take between 5 to 10 minutes depending on systems charge and ambient air conditions. When the can's temperature has equalized with ambient air conditions then proceed with next step. Be sure to check that all connections from can to unit are secure and that there is no leakage occurring.

 

9.  Turn handle (A) cw until it stops, isolating charged can from A/C or R unit.

 

10. While holding the can upside down, turn on A/C or R unit. Slowly turn handle (A) ccw gradually releasing SUPER SEAL TOTAL™ into the system. This should take approximately 3 to 5 minutes. Releasing SUPER SEAL TOTAL™ too quickly could result in liquid slugging. Shake can gently to determine when empty. If all of the contents in can are not emptied after 5 minutes then turn can-tapper piercing handle (A) cw until it stops. Turn off A/C or R unit and repeat steps 8, 9 and 10 as many times as necessary to empty contents of can. This should dislodge any particles that may have entered the can from the refrigerant system. If this fails, remove hose from low side service port, while A/C or R unit is on, and attach hose to refrigerant canister and charge can. Close valve CW and reattach can to low side of the A/C or R system. Slowly open valve ccw and inject SUPER SEAL TOTAL™ into system.  Proceed to step 11.

 

11. Once can is empty remove female fitting (D) from low side service port, while the unit is running.

 

12. Reclaim residual refrigerant from can and hose using a recovery machine. When finished reclaiming refrigerant, dispose of can and hose.

 

TAPPING VALVE AND HOSE NOT TO BE REUSED.

 

Eye Contact:  In case of contact with eyes, rinse immediately with plenty of water and seek medical advice

Skin Contact: Remove contaminated clothing. Wash with soap and water.  If irritation persists or if contact has been prolonged, obtain medical attention.