Mini Type
Wireless Remote Shutter Release for Nikon D700 D300 D200 D100 D3 D2 D1
as MC-30 MC-36
Introduction
This wireless shutter release has strong anti-interference function and has 16 channels for you to choose. It is extremely useful if there are several photographers working nearby. Each photographer could choose their own channel to trigger off the shutter release of the camera they are going to use without triggering others’ because of overlapping signals. You also can control more cameras with the channel switches on the transmitter and the receiver, and extra receivers if you need.
Features:
Raeceiver attached to the camera's hot shoe when Radio triggering with the Transmitter for operations.
Available to use the Receiver as a remote cable release without the Transmitter.
Also works without the Battery when using the Receiver as a remote cable
Wirelessly Trigger Your Camera's Shutter
-With the receiver connected to your camera's remote control socket, you can press the button on the remote control to trigger your camera's shutter wireless !
Two-Level Shutter Button, Autofocus, Continuous Drive & Bulb Mode Supported Too!
-The shutter button can be pressed halfway or all the way.
-You can activate autofocus, release shutter, activate continuous drive mode or keep the shutter open for bulb photography as well.
Important functions? Bulb Shutter(B.Shutter):
this SM-? Kit supports the Bulb shutter. To use Bulb shutter function, press the shutter button on the Transmitter for 4 sec. until the Red LED on the Transmitter is automatically off. You can see the Red LED on the Receiver is continuously ON during the performance. To release the Bulb Shutter, press the shutter button on the Transmitter shortly.
Dimensions:?
Transmitter (L x W x D):
82mm x 26mm x 15mm;
Receiver (L x W x D):
52mm x 39mm x 29mm;
16 Channels with Working Distance of?50 Meters!
-Strong resistance to interference.
-There are 16 channels available so that you can switch to other channels to avoid jamming frequency.
-Maximum working distance is about?50 Meters in open area without blockage.
Energy Saving Design, Long Working Hour
-With its low voltage and energy saving design, you don't have to change the battery often.
-With a new battery, the receiver standby time is about 1000 hours.
-With a new battery, the remote control can trigger about 20,000 times.How to Connect?
1. Switch off the camera.
2. Make sure the receiver and remote control are on the same channel (check the little switch on them).
3. Connect the receiver to your camera's remote control socket.
4. Press the button on the receiver to turn it on.
How to Use?
With the shutter button on the remote control, you can do the followings:
Turn on power:
-Turn on the power of Transmitter and receiver
-Turn on the power of camera
Autofocus:
-Press it halfway to activates autofocus. (Indicated by Green LED)
Release Shutter:
-Press it all the way to release shutter and take pictures. (Indicated by Red LED)
Continuous Drive:
1. Switch the camera to continuous drive mode.
2. Press it all the way to release shutter continuously.
Bulb Mode:
1. Switch the camera to Bulb mode.
2. Press it all the way for?4 seconds until the Red LED on the remote control goes off.
3. The receiver is in bulb mode now. (Indicated by Red LED on the receiver)
4. Press the button again to close the shutter.
Specifications:
| |
Transmitter |
Receiver |
| Power |
12V |
3V |
| Battery |
23A (included) |
CR2 (included) |
| Frequency |
433Mhz |
Specifications
- Transmitter x1
- Receiver x1
CR2 Battery (installed in receiver) x1
- 23A Battery (installed in remote control) x1
- English Instruction Manual?
Suitable For
Digital SLR
Nikon D700 D300 D200
Nikon D100(D100 must be used in combination with the MB-D100 multi-functional battery pack)
Nikon D1 / D1h / D1x
Nikon D2 / D2H / D2Hs / D2X
Nikon D3 / D3X
KODAK DCS Pro 14n DCS620
FUJI S3 S5 Pro/UVIR
Film SLR
Nikon F6
Nikon F5
Nikon F100
Nikon F90 / F90x
Nikon N90 / N90x
|