New LGB compatible DC DCC Power Supply 24V 12.5A 300W

The SL-PS300-1-27F regulated switching power supply outputs 24 volts at 12.5 amps. This supply matches the Digitrax DCS-200 8 amp & the Massoth 1210Z Central Stations, 1203B 12 amp boosters and with our SL-CB-6A circuit breaker with LGB wire harness can power the LGB Central Station and Boosters

• Universal AC input / full range with PFC (Power Factor Correction)
  
• Forced air cooling by built-in DC fan
  
• Cooling fan ON/OFF auto control
  
• Over load, over voltage, over temperature & short circuit protection
  
• 100% full load burn-in test
  
• 1 year warranty

PFC enabled efficiency:
Click here to learn why PFC saves the planet and your power

Input Voltage: 120 or 240VAC 47 to 63Hz

Input Current: 12.5 Amps(120VAC) 4 Amps @ 120VAC, 2 Amps @ 230VAC

Output Voltage: 24Volts (Front panel adjustable from 18.4 to 27.4 VDC

Output Current: 12.5 ADC (DC Amps) at 230VAC

Output Current: 300VA (300 watts) at 230VAC

Output Ripple: 150 mv (millivolt) Max. / 2 mv Typical

Dimensions: 215 x 115 x 50 mm

Weight: 2.6 pounds

Specifications:

• Enclosed regulated switching supply.
• Over Voltage protected
• Current protected
• LED output indicator
• Terminal strip In/Out
• PFC - Energy Efficient Switching Supply

M.T.F.B.: > 168K hours ( according to MIL-HDBK-217F at 25°C environment)

Safety approvals: UL, c-UL, TÜV, CB, CE.

Mounting: Bottom; 4 ea. 4-M4 L=5mm & 4ea. 5-m3 L=3mm brass threaded mounted holes. Side; 4 ea. 4-M4 L=6mm brass threaded mounted holes..

Cables: not included. (All cables are included but available for LGB Central Station and/or LGB Booster with our SL-CB-6A Circuit breaker and cable set)

Easily change the output voltage from the front panel

• Factory Set at 24 Volts

Boost the voltage to compensate for line voltage drops.

• 27.2 Volts Maximum

Lower the voltage to match your engines voltage requirements.

• 18.8 Volts Minimum

Protect your train's smoke stack heating element, lighting and electronics by setting the voltage of your choice.

• UL listed
• 10 feet long
• 3 wire cable
• Molded three prong AC plug
• ON/OFF switch located 1 foot from the end of the cable.
• Rated 300 Volts,
• 105 deg. C,
• 18 AWG with a center green ground wire.

1. Attach an AC grounded power cord to the power supply.
2. Attach 16 or 18 gauge wires between the supply and 1 or 2 SL-TLCF DC throttles.
3. Attach wires between the SL-TLC1cv and your track.

This combination provides 200VA of power and 24VDC PURE LINEAR POWER at 12.5 Amps continuous/30 amps peak. Maximum power supply output voltage can be adjusted from 18.8 to 27.2 Volts DC by turning the adjustment control on the supply front Panel. (See photos above)

Attach an AC grounded power cord to the power supply.

1. Attach two wires between the supply and your DCC central station or booster (Digitrax DCS 200 shown).
2. Attach wires between the DCC central station or booster and your track.
3. Plug in the power supply

The SL-PS300-1-27 power supply is a perfect match to the Massoth 1210Z 12 amp booster to provide 12 amps of continuous DCC power. The supply may also be used with other manufactures DCC central stations and boosters.

Use this supply and two SL-CB-6A Circuit breakers to power an LGB Central Station and LGB booster with >2X the power and 1/2 the cost of the LGB Transformer. The pure DC power also eliminates the problem of signals not getting to your locos by improving reliability of communication and the supply protects your LGB investment from over and under voltage as well as eliminating line noise from your railroad.

Get twice the power at 1/2 the cost and solve you LGB MTS reliability problems for good.

Hook up is done in minutes - just connect the Circuit Breakers to the power supply with a screw driver and then use the supplied wires on each circuit breaker set to power a central station or booster

Each SL-CB-6A Circuit Breaker comes pre-wired with a 12 and 24 inch 18 AWG power cables for easy hook up.

Each SL-CB-6A Circuit Breaker uses isolated crimp on connectors to allow easy removal of power cables for installation. CE and UL approved circuit beaker protects your LGB investment.

The Massoth 1210Z 12 amp Central Station or 1203B 12 amp booster and the SL-PS300-1-27 power supply is a perfect match for MTS/DCC use. The Massoth 1203 B is available now - check at the Shourt Line for more information. The 1203 B has three power units that can be used individually or together to supply 4, 8 or 12 amps of MTS/DCC power. Each of the three units has electronics for automatic loop control without additional hardware. The 1203B output voltage is adjustable from 14 to 22 volts making it applicable for all gauges. Use of NMRA standardized CDE connectors to connect the booster with the central station of your choice.

Massoth is the maker of all LGB electronics and Massoth is the only manufacture that makes DCC/MTS products that meet BOTH NMRA DCC standards AND LGB type I, II and III MTS standards. This means this is the only product line guaranteed to operate ALL your old and new LGB locomotives with type I, II and III decoders as well as all NMRA standard DCC products.

A perfect match; SL-PS300-1-27F (12.5A) + Massoth 1210Z central station, Navigator and receiver for ultimate wireless MTS/DCC Train Control.