A reserve price is the minimum price the seller will accept. This price is hidden from bidders. To win, a bidder must have the highest bid and have met or exceeded the reserve price.
This item , we provide two models the 110V and the 220V applicable to our global customer.
(The position of the two Temp-sensor when soldering the south/north board)
(Soldering the CPU plug of the computer motherboard)
(Soldering the GAP platoon of the computer motherboard)
(Soldering the expansion slot plug of the computer motherboard)
FEATURE
1.Adopt infrared weld technology which independent exploration.
2.Use infrared heat which is easy to cut through and make the parts heat evenly. This breakthrought get rid of the shortcoming of traditional weld machine with sirocco should cover the parts whenheating.
3.Easily operate. Just need one day training and you can operate it skillfully.
4.Don't need weld tools.This machine can weld all the components of 35-50cm.
5.This machine has 800W heating system.Preheating range is 240x180mm.
6.Infrared heatinghas no sirocco flow. Don't impact perimeter small components. It can be used to unsolder BGA,SMD,CSP,LGA,QFP and PLCC, especially Micro BGA and SMD elements.
7.Definitely can satisfy the request of sealing off/repairs of BGA about the computer, mobiles, notebook, the electricity games and so on, especially suits to the computer north and south bridge.
Operation method:
1. Inspects and Starting up
Please inspects the infra-red lamp body, the temperature sensor and the power line first whether connects good befor you starting up. Turns on the power switch. Use if after pass the self-checking (the panel display shows the setting value which useed last time. The front panel has two switches, controls the preheating chassis, the infra-red lamp body work separately; Presses the front panel “IR PRE-HEAT PIATE”’ “▲”“▼”;,the range between 60-200; in, the adjustment preheating chassis preheating temperature, presses the switch is “ON”;, then the preheating chassis starts to work, presses the switch is “OFF”;, then preheating chassis knock off; Presses the front panel IR HEAT LAMP”’” “▲”“▼”; can adjusts the infra-red lamp body the operating temperature between200-350 , presses the switch is “ON”;, then the infra-red lamp body starts to work, presses the switch is “OFF”;,then infra-red lamp body knock off.
2. Sealing off /repair operation
Pleacement of the PCB board
Make the select PCB board aim to the rabbet on the splint and put on the PCB board braket, fasten the handwheel of the PCB boar splint and fasten the PCB board. Move the splint sliding guide from right to left in order to choose the suitable position.
Before sealing off/repair
adjustment and preparatory work befor unsolder/repair operation
Adjusts the position of PCB board, make the center of the chip which needs unsolder/repair aim to the facula center of the infrated lamp body. Adjust the height of the lamp and the height of 20-30mm is suitable distance between the lamp tap and the unsolder object
Lays aside the infra-red lamp the temperature sensor nearby the chip on the suitable position, all around spreads the welding flux in the chip with sensor (to weld treasure or burnt oil), does this may cause the sensor to measure the temperature is more accurate, simultaneously is helpful the solder to help welds the function, BGA welds the plate to be able to be completer, can prevent effectively welds the plate to stick and questions and so on tin wool.
When the chip has spreads the waterproof solid sealing compound, it certainly must be first open the preheating chassis melt rubber, after lets rubber being heated soften or the pulverization, cleans up first; Also available sol hydrosol and so on .
measures.According to sol temperature which the factory provides, carries on sol processing, the melt rubber temperature is not suitable excessively high, generally for 120-140℃ the suitable preheat interval is 3 - 5 minutes or longer.
Sealing off/repair process
According to product technological requirement or PCB board size, adjustment preheating chassis preheating temperature( 60-200℃; adjustable), may open the preheating chassis in advance, one 3 - 5 minutes, the preheating chassis can stabilize in the temperature range which supposes in advance
According to the chip size and the welding technological requirement, it selects the suitable infrared lamp and the adjustable heating temperature is (200-350℃), and it can satisfy the sealing off/repair technological requirement then.
The common experience is: According to the repair chip size,it can adjust ouput temperature of the infra-red lamp suitably the output temperature about 220-240℃; (adjustable) and chassis preheating temperature (60-200C; adjustable);When the sealing off/repair is smaller than the 20x20mm chip, it may adjust the infra-red lamp temperature to 220-240C; about, if the chip has not spread the waterproof solid sealing compound, or the PCB board is small it cannot distort, but it does not operate the preheating chassis preheating; Otherwise the first preheating degree between120-140 is suitable; According to the craft and the user experience, when 30x30mm chip opens in a big way, it may adjust the infra-red lamp 240-260; about, preheating chassis 140-200C;, first preheating 3 - 5 minutes, after the chassis is supposing stablly in advance the temperature, may complete the sealing off/repair process very conveniently; This time the infrared light is the strongest, the chip temperature elevates quickly and pays attention to the control specially, prevented the sensor displacement, the temperature measurement does not permit,the time of the chip being heated is long, the elevation of temperature is too high, and it is bad for the chip.
The disassemble operating process is generally: The fixed PCB board, adjusts the PCB board the position, adjusts the chip which the infra-red lamp the heartfelt alignment disassembles, adjusts the infra-red lamp, lays aside the infra-red lamp highly the temperature sensor, spreads the welding flux, the hypothesis preheating chassis preheating temperature and the infra-red lamp operating temperature, the opening preheating chassis, after 3-5 minute or a longer spot, preheating temperature control the nearby setting value, the opening infra-red lamp heating chip, achieved supposes the temperature or the chip tin plate in advance melts, takes down the chip after the real suction pen or the tweezers, closes the infra-red lamp and the pre-heating platen switch, and so on main engine full cooling, closes the power source.
Returns to the operating process which welds is generally: Operating process basically with disassemblage process.The similarity is: Cleans up first welds the plate and plants the tin ball, the preheating PCB board, the correct laying aside chip, the craft temperature which returns according to the tin ball welds carries on, the backflow welding, cooling preheating. May enhance the temperature to 20-30 degree again regarding the non-lead solder component
In the sealing off/repair process matters needing attention and the correlation showed that,
When sealing off/repair quite big PCB board chip, for instance: The computer board must certainly carry on the fully imposite the preheating seasoning, may the technological requirement which support the factory carries on, it also may depend on the experience of the process; Only then processes appropriately, can prevent effectively when sealing off/repair chip, the PCB board distortion and produces from this faulty soldered joint, chip rake.
In the sealing off/repair process, the infra-red lamp shines in the region, all plastic plug-in unit, carries on the cover using the aluminum tin foil, prevented high temperature infrared dries the distortion or the harm.But it is completely not wraps.
Returns to PCB board which welds/repairs, after cooling, after cleans first, dryly, carries on the test; If it is not good, may return welds again.Again not good repetition entire process.
Around the work, thank to has not put the PCB board in the situation, may not the long time opening infra-red lamp, be able to reduce the lamp the service life; Forbid strictlys shining the counter-optical very strong reflection with the infra-red lamp long time, can affect the lamp seriously the life.
3.Maintenance and overhaul
Complete machine maintenance: After the machine uses period of time, please to the focusing frame
, the guide pillar, the PCB board support and so on . the slipper, regularly with fat cleaning, the maintenance lubricates and guards against rust the goal.Preheating chassis and infra-red lamp body maintenance: The preheating chassis and the infra-red lamp body, specially the infra-red lamp high insightful protection slide, regularly with dehydrated alcohol cleaning, the elimination welding flux condensate, maintains the infrared hot radiation unobstructed.Infra-red lamp replacement: When replaces the infra-red lamp, with the special-purpose inside caliper gauge or the long mouth pliers, will fix the slide first the spring inside caliper, the slide, spring inside caliper one time takes down; Again takes down the fixed infra-red lamp the spring inside caliper, then with the bamboo slip or the wooden bat outside lamp chimney air vent place, goes against the infra-red lamp gently, draws out the lamp holder to replace the new infra-red lamp; Installs again according to the opposite order .
4.Suggestion:
About the components without plumbum, you should add 20-30℃.
About the PCB board with components on its both side, please set-up the pre-heat temperature lower, and then use the IR-Lamp to heat.
5. Cooling the machine
Turn off the switch of the pre-heat dish and the IR-lamp.
Once the machine is cooling enough, cut off the power cable.
6 Attention
①When you maintain some large chip of the PCB board such as the mother board of the computer, you must pre-heat and dry the whole board first, then you can avoid the transmuting of the PCB board and soldering joint and rake angle of the chip.
②All the plastic plug-in board must be covered with aluminium-foil paper, to avoid transmutation or destroying.
③The PCB board which had been maintained, after cooling, clean it, and do the test when it is dry. If it is not ok, re-soldering it.
④Around working, when the PCB board is not on the holder, please do not long time open the IR-lamp, do not shoot the light on the strong glisten objects. Otherwise it will reduce its using time.
⑤About the chips which is encapsulation simply, please pre-stick aluminium-foil paper on the centre of the chip, to avoid burning out the slice of silicon.
The measurement of the aluminium-foil paper had better a little larger than the slice of silicon, but not too large. Otherwise, it will do effect on the soldering.
Technology parameter Instrument inventory
Welding table main body
1
Infra-red lamp body
1
Temperature sensor
1
PCB bracket
1
International Power line
1
user'smanual(Compact disc)
1
Work floor size
360X240mm
Rated voltage and frequency
AC220-230v 60/50Hz
Complete machine power
1000W
Infra-red lamp body power
150W
Infra-red Preheating chassis power
800W
Infra-red lamp body heating size
70mm(50x50mm)
Preheating chassis preheating size
240x180mm
Infra-red lamp body temperature adjustable
200C-350C
Preheating chassis temperature adjustable
60C-200C
as follow
The product we are offering is 100% Brand New in their original boxes. Never Used, Never Grey Market.
It comes with all the manufactured accessories, books, manuals & software.
Within minutes of placing your order, we will automatically email you detailed information on how to complete your order. This email will be sent to the email address that you have registered with eBay. If you have not received this email from us, you can call us at +86 13837108448 ..
Please do not buy if you don't intend to pay!
For the protection of both buyer and seller, we reserve the right to request further verification and other information before completing an order.
Payment must be received within 7 days after the end of auction. Unpaid auction will be forfeited after 7 days and a Non-Payer report will be filled in order to offset the administration fee.Payment will be refunded at original currency only.We will not responsible for any loss due to exchange rate difference in the refund process.We reserve the rights to CANCEL the bid from who has Negative feedback.Such bidders please contact us before bidding.All selling products are brand new, never been used and not refurbished. All images are for illustrative purposes only. Please leaves the feedback for us when you received the product, we will treat you in the same way.Please feel free to contact us if you have any enquiries. Otherwise, you are fully agree about the policies.
Paypal You don't need to have a Paypal account to pay now. Paypal can now charge your credit card directly:
Order will be processed upon payment received. If you pay by eCheck, we will process the order upon the clearance of the fund which takes usually 4 business day.
Money Order Please make your money order payable to HARVEST ONE LIMITED. We will ship you the item(s) within two working days upon cashing the money order. We DO NOT accept postal money orders, including those issued by USPS.
INTERNATIONAL SHIPPING:
All of products will be shipped as ‘Gift’or "sample", and we always try the best to Legally Minimize your import duties (or GST or V.A.T. or other Taxes). In the most cases of shipping, there is none duty payable. However, buyers are responsible for any additional charges generated for customs in your country/state.
Import duties and taxes, as well as additional charges for customs clearance, if any, must be borne by you. As custom duty varies from country to country and place to place, we are in no position to check the rate for you. Please check with your local customs if it is of any concerns to you or check with your country 's customs' office for exact charges before placing your bid.
We ship worldwide from China using FEDEX, DHL, UPS ,TNT or Truck Freight when needed. Please choose the shipping sevice listed in order that your item can arrive to you safely and early. We will combine multiple order to reduce shipping and handling fees when possible. All shipments are fully insured.We will sent out the item via China Registered Airmail within 3-5 working days. The shipment usually takes 3-15 working days according to the shipping service chosen to your PayPal Registered Address. Please provide detailed address and recipient's full name in PayPal. We are not responsible for any lost due to wrong address and unmatch recipient's name. The Shipping and Handling rate is fixed and non-refundable.
USA Canada Mexico
FEDEX UPS EMS 3-5
working days
USD 170．00
GermanyFrance
Italy United Kingdom
FEDEX UPS EMS 3-5
working days
USD 180.00
Spain Sweden
Denmark Netherlands
DHLTNT EMS 3-5
USD 185.00
working days
Czech Republic Poland
TNT EMS 3-5
working days
USD 195.00
Israel
TNT５-７working days
USD 210.00
Brazil
FEDEX UPS ５-７working days
USD 235.00
Australia
TNT ３-５ working days
USD 155.00
Returns:
We offer an exclusive 30 day return policy.
All our Soldering Tools are provided one year warrantee by us from the date you make a purchase. An replacement or repairment (not including Nozzel and Heating Element) will be provided by us for free when a faulty is developed within the warrantee.
All returns must accompany a Return Merchandise Authorization (RMA) number. To obtain a RMA number, you will need to call us +86 371or email us at gms_taurus@hotmail.com. Any returns that don’t have a RMA number on it, will be sent back to you. In addition, refusal of delivery is not a means of returning an item. If you do refuse a delivery, you will be charged for the return shipping on the way back to us. We will ask you to pay the price determined by UPS to ship the product back to us.
All returns are subject to a re-stocking fee. A re-stocking fee can range between 5-15% depending on the condition of the return. For further questions please call us at +86 371 68869905 or email us at gms_taurus@hotmail.com. Shipping & insurance costs are non refundable.
GSM-TAURUS Warranty Return Policy: GSM-TAURUS is guaranteed to be in working and warranted for one full year. All warranties are issued by our company, and the manufacturer. If the unit is found defective(except the artificial damage and the improper use) within one year of the invoice date, return it for a free rapair.( If you need to make a warranty return claim, please contact us at gsm_taurus@hotmail.com or or call+86 371 67767737. Our obligation shall be limited to the repair or the replacement , at our choice , of any such defective product free of charge to our sustomer. If we decide that the cannot be repaired or replaced, we shall credit your account in an amount equal to the sum you paid us for it.
GSM_TAURUSNon-Warranty Return Policy：If you are dissatisfied with a product from us , you may return the product(without any damage) within 30 calendar days since the invoice day. A 40% restock admistration fee and the freight out and home will apply to all non-warranty returns.Non non-warranty returns will be accepted 30 days after the invoice day.( If you need to make a non-warranty return claim, please contact us at gsm_taurus@hotmail.com or call+86 371 67767737 .
Please email us or make a call to get more information
Q: Hello I want to buy this machine and a reballingkit with stencils . Can you make
an offer for the kit and machine incl shipping to the netherlands ?? thanks regards john
A: Hi my friend,
I'm glad you interestd in this item!The shipping cost to European country is 150USD!Kind regards!
*The estimated delivery time is based on the seller's handling time, the shipping service selected, and when the seller receives cleared payment. Sellers are not responsible for shipping service transit times. Transit times may vary, particularly during peak periods.
Back to Search Results
) 
GSM-TAURUS
Print
Report item
USA 
Canada 
Mexico 
Germany
France 
Italy 
United Kingdom
Spain 
Sweden 
Denmark 
Netherlands 
Czech Republic 
Poland 
Israel 
Brazil 
Australia 
and your 
